E hlahisitsoe ke Bethel, Conn.-based Society of Plastics Engineers, kopano ea selemo le selemo ea botekgeniki ea polasetiki e tsejoang e le Antec e kopana le NPE 'me e tla qala May 7-10, 8 am-6 pm, Orange County Convention Centre e Orlando, Fla. SPE e lebeletse ho hohela batho ba 1,500 ba tlileng kopanong le ho ba le lipuo tse fetang 550 tsa khoebo le tsa botekgeniki.
Libui tse 'ne tsa kopano ea matsatsi a mane ke Scott Schiller oa HP Inc., Rajen Patel oa lefapha la Performance Packaging la Dow Chemical Co, John Beaumont oa American Injection Molding Institute le Beaumont Technologies le moprofesa Phil Coates oa Univesithi ea Bradford Engelane le Setsi sa Lipatlisiso sa Polymer Interdisciplinary.
SPE e tla boela e ananele le ho hlahisa baithaopi bao e leng baithaopi ba bacha ka ho fetisisa ba nang le boemo ba Litho tse Hlomphehang tsa Tšebeletso: Luyi Sun oa Univesithi ea Connecticut le Uday Vaidya oa Setsi sa Advanced Composites Manufacturing Innovation.
SPE e tla boela e hlomphe batho ba bacha ba robong - Ashok M. Adur, Carol Forance Barry, Mehmet Demirors, Dan Falla, John W. Gillespie Jr., Tie Lan, Russell Speight, Uttandaraman Sundararaj le Michael Thompson - ho Antec.Ho tloha ha ho qalisoa ka lekhetlo la pele ka 1984, SPE e boletse litho tse 334 e le balekane.
Ho qala ka Sontaha sa la 6 Mots'eanong, ho tloha ka 2-4 mantsiboea ka phapusing ea N320FGH, ke Cross-Link Your Network, moqoqo o bulehileng o tsamaisoang ke litsebi tsa indasteri ea bacha le baithuti mabapi le ho nka monyetla oa Mokhatlo oa Baenjiniere ba Plastiki ho thusa ho tsamaisa mesebetsi ea thuto le litsebi.Cross-Link Your Network e kile ea tsejoa e le Pilot Our Future.
Ho na le liketsahalo tse peli tsa SPE Next Gen ka Mantaha oa la 7 Mots'eanong: Seboka sa Boto ea Boeletsi ba Next Gen ho tloha ka 8-11 hoseng ka phaposing ea N320E le FLiP le Sip Reception, hape e hlahisitsoe ke Baetapele ba Bokamoso ba Mokhatlo oa Plastics Industry ka Plastiki, ho tloha ka 4:30-6 :30 thapama ho Valencia Ballroom Foyer e Karolong ea 4 ea Kaho ea Bophirima.
E bulehetse liithuti feela, lijo tsa mots'eare tsa baithuti li tla tšoaroa ka Laboraro la la 9 Motšeanong ho tloha ka 12:30-2 pm ka phaposing ea W414AB.
Bahlōli ka mekhahlelo e mene, hammoho le Khau ea People's Choice le Khau e kholo, ea SPE Plastics for Life Global Parts Competition ba tla phatlalatsoa ka Laboraro la la 9 Motšeanong, ka mor'a ho ahlola ka la 7-8 Motšeanong phasejeng e ka ntle ho likamore tsa lenaneo.Likarolo tse 'ne tse thehiloeng ho likarolo ke Ho Sireletsa Bophelo (polokelo, polokeho, sephutheloana le ts'ireletso), Boleng ba Bophelo (ho sisinyeha, puisano, mabothobotho / boiketlo, boikhathollo le boithabiso), Ho Ntlafatsa Bophelo (thuto, matla, monyetla le bophelo bo botle) le Ho Tšehetsa Bophelo. (tikoloho, paballo, moshoelella, ho nchafatsa le ho fokotsa).
Khau ea maemo a holimo ea tlholisano, e leng Khau e kholo, e ea karolong e maemong a holimo ka ho fetisisa har'a batho ba khethileng likarolong tsohle tse 'nè.Motho ea hapileng Khetho ea Batho o khethoa ke ba tlileng kopanong ba Antec bao e seng basebeletsi ba SPE, litho tsa komiti ea Plastics for Life kapa baahloli.
Sehlopha sa baahloli se kenyelletsa bapresidente ba nakong e fetileng ba SPE, basebetsi-'moho le SPE, litho tsa mecha ea litaba le litsebi tsa indasteri.
Hape ho Antec ho na le Lijo tsa hoseng tsa Khokahano ea Basali ka 7-8:30 hoseng, Labobeli la la 8 Motšeanong, bakeng sa litsebi tsa polasetiki le baithuti, moo libui li tla arolelana liphihlelo tsa tsona tsa ho sebetsa indastering.Ketsahalo ena e tla laoloa ke Vicki Flaris, moprofesa ea feletseng Bronx Community College le mopresidente oa nakong e fetileng oa Mokhatlo oa Plastics Engineers.
Libui nakong ea lijo tsa hoseng e tla ba Shelley Fasano, motlatsi oa mopresidente oa ts'ebetso ea Dymotek Corp.;Heather Meixel, mopresidente oa Bamar Plastics Inc.;Wesleyne Greer, mookameli e moholo oa thekiso ea Materia Inc.;le Judy Carmein, molaoli oa lihlahisoa tsa lefats'e oa CNC machining bakeng sa Proto Labs Inc.
Ngoliso ea hlokahala.Banna le basali ba amohelehile ho ba teng.Lijo tsa hoseng tsa Khokahano ea Basali li tla tšoareloa ka phaposing ea N310FGH.Ho fumana lintlha tse ling, etela www.eiseverywhere.com/ehome/252707/700179.
8:30-9 am: Phetoho ea PLA bakeng sa Ntlafatso ea Layer-to-Layer Adhesion in 3D Printed Parts, Michael Thompson, McMaster University
9-9:30 am: Tšusumetso ea Nako ea Lera holim'a Thepa ea Karolo e Hlahisang ho Fused Deposition Modeling Process, Frederick Knoop, Paderborn University-DMRC
9:30-10 am: Liphello tsa Polymer Rheology ho Predicted Die Swell le Fiber Orientation in Large-Scale Polymer Composite Additive Manufacturing, Zhaogui Wang, Baylor University
10-10:30 am: Mechanical Properties of Reinforced Compounds for Large-Format Additive Manufacturing, Rabeh Elleithy, Sabic
10:30-11 am: The Influence of Melt Flow Rate and Nozzle Themperature in Fused Filament Fabrication, Nicole Hoekstra, Western Washington University
11-11:30 am: Mechanical Properties of 3D Printed Polylactide/Microfibrillated Polyamide Composites, Nahal Aliheidari, Ph.D.Seithuti, Univesithi ea Washington State
8-8:30 am: Ntlha ea Bohlokoa: Boqapi Limmarakeng Tse Holileng: Ho Utloisisa Mekhoa ea Lefatše ka Bophara ho Bohlokoa ba Ketane ea Boleng le Tsoelo-pele e Potlakisang, Narayan Ramesh, Dow Chemical Co.
8:30-9 am: Melt-Mastication of Isotactic Polypropylene for Ntlafatso ea Thermal and Physical Properties, Brian Cromer, R&D, Arkema LLC
9:30-10 am: Mekhoa ea ho Ntlafatsa Thermoelectric Properties of Melt Mixed Polypropylene-Carbon Nanotube Composites, Petra Pötschke, IPF Dresden
10-10:30 am: Analysis of Newly Developed Textured PTFE Gaskets Subjected to Creep Relaxation, Ali Gordon, University of Central Florida
10:30-11 am: Sebopeho se Ipehileng Tefiso Storage le Emi Shielding Tshebetso ea Thermoplastic Elastomer Nanocomposites E Nang le MWNTs, Shital Pawar, Univesithi ea Calgary
8-8:30 am: Phallo, Motsoako le Boitšoaro ba Polymer Reactive Blending in Twin-Screw Extruder, Cailiang Zhang, Univesithi ea Zhejiang
8:30-9 am: Phello ea High-Speed Twin- and Quad-Screw Compounding on the Molecular Weight, Molecular Weight Distribution, le Mechanical Properties of Polyethylene Composites, Mansour Albareeki, Ph.D.seithuti, UMass Lowell
9-9:30 am: Tlhahlobo ea Teko ea Fill Ratio, Resin Pressure, Resin Temperature E Fumanetsoeng Ho Tsoa ho 2.5D Hele-Shaw Model ka Phallo ea Cororating Twin-Screw Extruder, Masatoshi Ohara, Toshiba Machine Co. Ltd.
9:30-10 am: Ho Rala le ho Tiisoa ka Phatlalatso ea Lintho tse Atolositsoeng tsa Motsoako bakeng sa Ntlafatso ea Metsoako e Ntlafetseng ea Ts'ebetso ea Extrusion, Vivek Pandey, Case Western Reserve University.
10-10:30 am: Characterization of Stress in a Twin-Screw Extruder for Processing and Extrusion of Extrinsically Self-Healing Thermoplastics, Connor Armstrong, University of Maryland, College Park.
10:30-11 am: Phatlalatso e ntlafetseng ea Nanoclay ka Ethylene Vinyl Alcohol ka Sub-Critical Gas-Assisted Processing, Thomas Ellingham, Ph.D.seithuti, UW-Madison
11-11:30 am: New Involute Extruder Screw Elements for Ntlafatso ea Tlhahiso le Boleng, Paul Andersen, Coperion
11:30-12 pm: Ho Rarolla Mathata a Phepelo bakeng sa Metsoako e Khethehileng ho TriVolution Compounder, Gonzalo Marulanda, B&P Littleford
8:30-9 am: Nts'etsopele ea Meetso ea Phallo ea Limolek'hule bakeng sa Ultrasonic Welding ea PLA, Karla Lebron, seithuti se fumaneng mangolo, Univesithi ea Iowa State
9-9:30 am: Liphello tsa ho Aha Boithuto le ho Tlatsa Boemo ba Mechanical Properties of Fused Deposition Modeling PLA, Avraham Benatar, The Ohio State University
9:30-10 am: Correlating Ultrasonic Weld Quality With Melt Layer Thickness, Alex Savitski, Dukane IAS
10-10:30 am: Ho Utloisisa Meltdown Nakong ea Quasi-Simultaneous Laser Transmission Welding, Philip Bates, Royal Military College of Canada
10:30-11 am: Patlisiso ka Temperature Field of Laser Transmission Welding Polycarbonate Based on 3D Real Surface Topography, Zhong Hongqiang, Soochow University
11-11:30 am: Temperature Field le Fluid Field Simulation of Laser Transmission Welding Polycarbonate, Yan Tingpei, Soochow University
8-8: 30 am: Tekolo ea Lisebelisoa tsa Li-Plumbing tsa Polybutylene Ka mor'a Tšebeletso ea Nako e Telele, Dale Edwards, Engineering Systems Inc.
8:30-9 am: Tshebetso ea PE Pipe Resins in Chlorine Dioxide Containing Aqueous Solution, Márton Bredács, Polymer Competence Center Leoben
9-9:30 am: Quantifying Oxidative Degradation in Polyolefin Pipe ka IR Spectroscopy, Don Duvall, ESi
9:30-10 am: Lipatlisiso tsa Pipe Quick Burst Pressure ea Sample Length on Two Plastics, Bryan Hauger, Hauger Consulting
10-10:30 am: Innovative Millimeter Waves Technology for Measuring Diameter, Ovality, Botenya ba Lebota le Ho Saging ha Lipeipi tse Khōlō tsa Plastic, Katja Giersch, SIKORA AG
10:30-11 am: Liphello tsa Primer ho Mechanical Behavior ea CPVC Pipe, Bingjun Chen, Univesithi ea Alberta
11-11:30 am: Fracture Mechanic Principles for Multilayer Pipe-Wall Design, Florian Arbeiter, Montanuniversität Leoben
8-8:30 am: Tlhahiso e Kenyellelitsoeng ea Lisebelisoa tse Khōlō tse Laoloang ke Ente tse Laoloang ke Mocheso ka Arc Welding le Diffusion Bonding, Johannes Ullrich, Hochschule Schmalkalden
8:30-9 am: Ho Laola Thepa ea Karolo ea Lehae ho Sebelisa Taolo ea Mocheso e Arohileng ka Enteng Molding, Mauritius Schmitz, Institute of Plastics Processing (IKV) ho Indasteri le Mesebetsi ea Tsebo ea Tsebo.
9-9: 30 am: Litšobotsi tsa Lits'ebetso tsa ho Tlatsa le Mechanical Properties of Micromolded Features, Jiang Jing, Univesithi ea Zhengzhou
9:30-10 hoseng: Nako ea Open Lag ea Valve Gate ho Sisteme e Tloaelehileng ea Semathi se Chesang, Byungohk Rhee, Univesithi ea Ajou
10-10:30 am: Ente Molding Setup ka Mekhoa ea ho Ithuta ka Mochini e Thehiloeng ho Ketsiso le Boitsebiso ba Teko, Julian Heinisch, Institute of Plastics Processing (IKV) in Industry and the Skilled Crafts at RWTH Aachen University
10:30-11 am: Ho Ithuta ka Tlhahlobo ea Optical ea Ho Adhesion ea Bokaholimo ho Multilayer Injection Molding Process, Byungohk Rhee, Univesithi ea Ajou
11-11: 30 am: Mohlala oa Ejection e Thusang ka Ultrasound ka Micro Injection Molding, Giovanni Lucchetta, Univesithi ea Padova
8-8:30 am: Lihlahisoa tse Ncha tsa Khalase ea Matla a Holimo, e Botlaaseng ba Likhalase tsa Ultra-Lightweight Composite, Stephen Amos, 3M
8:30-9 am: Li-Filler tsa Ts'ebetso e Phahameng: Mekhahlelo e Pharalletseng ea Ntlafatso e nang le likaroloana tse nyane, Péter Sebö, Quarzwerke GmbH
9-9:30 am: Litlhaloso tse Ncha tse Tsoang ho Phatlalatso e Ikemetseng ea Li-Nanotubes tsa Carbon tse nang le Multiwalled ka ho Optimization ea Melt Mixing Parameters Nakong ea Tlhahiso ea Nanocomposites e thehiloeng ho Polypropylene, Valérie Lison, NANOCYL.
9:30-10 am: Acrylonitrile Butadiene Styrene/Mica Composites: Tokisetso le Sebopeho, Mohammed Alghamdi, Yanbu Industrial College
10-10:30 am: Ntlafatso ea Lipalopalo ea Litlatsetso bakeng sa Khalase e Tlatsang Polypropylene Stabilization, Syed Hassan, A. Schulman Inc.
10:30-11 am: The New Carbon Black for High Jetness and Easy Dispersion, Marc Delvaux, Cabot Corporation
8-8:30 am: Nts'etsopele ea Elongational Mixing Geometries for Twin-Screw Compounding Extruders, Adam Dreiblatt, CPM Extrusion Group
8:30-9 am: Ho Tobana le Mathata a Mathata a Bokamoso ka RingExtruder RE, Erdmann Michael, Extricom Extrusion GmbH
10:30-11 am: Ntlafatso ea Theknoloji ea Coperion Pelletizing: Ke Eng e Ncha le Hobane'ng?, Mike Bickley le Eberhard Dietrich, Coperion
1:30-2 pm: 3D Printing Feedstock From The Recycled Materials, Nicole Zander, US Army Research Laboratory
2-2: 30 pm: Ho lekola Ts'ebetso ea Acrylonitrile Butadiene Styrene e Tsoelang Pele e Matlafalitsoeng ka Thermotropic Liquid Crystalline Polymer ka Fused Filament Fabrication, Mubashir Ansari, Virginia Polytechnic Institute le State University.
2:30-3 pm: Matla a Phahameng a Matla a Polycarbonate Filament for Additive Manufacturing, Sarah Grieshaber, Sabic
3-3:30 pm: Matla a Tlamahano ho Likarolo tsa Plastiki tse Ekelitsoeng ka Moetso oa Multimaterial, Jakob Onken, Setsi sa Ts'ebetso ea Plastiki Univesithing ea RWTH Aachen.
3:30-4 pm: Crystallization Kinetics during Materials Extrusion-Based Additive Manufacturing of Polycaprolactone, Kalman Migler, NIST
4-4: 30 pm: Ho nahanela ho sebetsa: Cellulose Nanocrystal Thermoplastic Urethane Filament Production, Jacob Fallon, Virginia Polytechnic Institute le State University
4:30-5 pm: Likamano tsa Sebopeho le Thepa tsa Polyphenylene Sulfide e Eketsehileng ka Matla a Carbon Fiber, Peng Liu, Oak Ridge National Laboratory.
5-5:30 pm: Tlhahlobo ea Matla ea Mehlala e Fused Fabricated Continuous Carbon Fiber Composite Test Samples, Rogelio Herrera, Univesithi ea Wisconsin-Madison
5:30-6 pm: Ho Ntlafatsa Ts'ebetso ea Motlakase ea PC/ABS Printing Filament for Fused Filament Fabrication using Carbon Nanostructures, Nicole Hoekstra, Western Washington University
6-6:30 pm: Rheological Characterization and Quality Assessment of Commercial ABS Filaments for Fused Deposition Modeling, Adam Miller, Shawnee State University
1:30-2 pm: Keynote: Global Automotive Color Trend, Popularity and Who's Driving, George Ianuzzi, Sandream Impact LLC
2-2:30 pm: Tlhahlobo ea Titanium Dioxide Photo-Activity in Polypropylene, Philipp Niedenzu, Chemours
2:30-3 pm: Ho Utloisisa Warpage ka Injection Molded Thermoplastics: Lisosa le Litharollo tsa morao-rao tsa Pigmentary, Breeze Briggs, BASF Colours & Effect USA LLC
3-3:30 pm: Ho Atolosa Meeli: Bismuth-Based Pigments for the Plastics Industry, Cristina Zanzottera, DCC Maastricht BV
3:30-4 pm: Ntlafatsa Mmala: A Pigment- and Surface-Chemistry Perspective, Christopher Beier, Clariant Plastics and Coatings USA Inc.
4-4:30 thapama: VOC Ho fokotsa Li-additives bakeng sa Masterbatches le Lingoloa tsa ho qetela tsa Polymer, Rob Lorenzini, Sehlopha sa Maroon
1:30-2 pm: Phello ea Khetho ea Resin ho Pore Formation ea Polyethylene Films, Wenyi Huang, Dow Chemical Co.
3-3:30 pm: Tšusumetso ea Liphutheloana tsa Plastiki ho Liphello tsa Cycle Cycle in the US and Canada Substitution Analysis, Emily Tipaldo, American Chemistry Council.
4-4:30 thapama: Boitšoaro ba Filimi ea Mohlala ho Likopo tsa Unitization tsa Pallet, Pavan Valavala, Dow Chemical Co.
4:30-5 pm: Fokotsehe Density Nylon 6/6 Compounds for Extrusion Applications, Ying Shi, A. Schulman Inc.
5-5:30 pm: Kamano Pakeng Tsa Sebopeho le Thermal le Mechanical Properties ea Thermoplastic Polyester Materials, Jeffrey Jansen, The Madison Group.
5:30-6 pm: Phello ea Annealing ho Viscoelastic Behavior of Polyetheretherketone, Zhiyuan Jiang, Texas A&M University
1:30-2 pm: 3D Numerical Simulation of Multiphase Flow in Partially Filled Twin-Screw Extruders, Hossam Metwally, ANSYS Inc.
2-2:30 pm: Mechanical Properties of Ultrahigh Molecular Weight Polyethylene Nascent Fibers at Different Screw Speeds, Fangke Liu, seithuti, Beijing Institute of Technology
2:30-3 pm: Lintlafatso tsa Viscosity le Phatlalatso ho Polyethylene Terephthalate Compounding, Prakash Hadimani, Steer Engineering
3-3:30 pm: Ho ntlafatsa Thermal Conductivity ea PVDF/Graphene Nanocomposites ka Metsi-Assisted Mixing Extrusion, Han-xiong Huang, South China University of Technology
3:30-4 pm: Liphello tsa Novel Extensional Mixing Elements mabapi le Fiber Length Distribution in Composite Extrusion, Molin Guo, Case Western Reserve University
4-4:30 pm: Transition Metal Dichalcogenide Thermoplastic Composites e Lokisitsoe ho Sebelisa Lab Scale Extrusion, Joshua Orlicki, Sesole sa US Laboratory Research
1:30-2 pm: Micro Injection Molding of Polypro/Graphite Composite, Shengtai Zhou, University of Western Ontario
2-2:30 thapama: Taolo e Tšoanang ea Foaming ea Phokotso ea Boima bo Phahameng ba Ente ea Microcellular Molded Thermoplastic Elastomer e Sebelisa Khatello ea Khatello ea Khase, Chang Che-wei, Chung Yuan Christian University
2:30-3 pm: Mechanical and Rheological Characteristics of PP/PET Blend With Maleic Anhydrite and Jute Fibre, Abul Saifullah, Swinurne University of Technology
3-3:30 pm: Mechanical Properties of Polyamide 6/Zeolite Composites, Davoud Jahani, Univesithi ea Bonab
3:30-4 pm: Liphello tsa Ts'ebetso ea Li-Parameters ho Phatlalatso ea Bolelele ba Fiber le Matla a Tensile a Long Glass-Fiber-Reinforced Nylon 6/6 Composites Mold Parts, Hsin-Shu Peng, Feng Chia University
4-4:30 pm: Ho lekola Ts'ebetso ea Sefofane sa Likarolo Tse bōpiloeng ka Tšimo ea Magnetic ka Ts'ebetsong ea Ente ea Ente, Chiu Min-Chi, Chung Yuan Christian University.
4:30-5 pm: Ts'ebetso e Ntlafetseng ea Ultrahigh Molecular Weight Polyethylene ka Supercritical Nitrogen le Carbon Dioxide ho Ente Molding, Galip Yilmaz, Wisconsin Institute for Discovery Univesithing ea Wisconsin-Madison
5-5: 30 pm: Phello ea Khatello ea Khatello ho Shrinkage le Warpage ea likarolo tse entsoeng ka ente, Zhiliang Fan, Moldflow R&D Center, Autodesk
5:30-6 pm: Ho ithuta ka Viscoelasticity ho Warpage Validation, RuJing Jhang, CoreTech System (Moldex3D) Co., Ltd.
1:30-2 pm: Khoebo ea Khoebo: Mathata a ho Theha Setso sa ho Qala, Bonnie Bachman.
3-3: 30 pm: Data Sciences le Domain Expertise Kopanya Mabotho ho Fetola Strategic Industrial Marketing, Bala Ambravan
3:30-4 pm: The Third Sustainability Survey of the Plastics industry, Bonnie Bachman, Shristy Bashyal, Maggie Baumann
2-2: 30 pm: Tlhokomelo ea Boleng ba Likarolo Tse Potolohileng tse bōpiloeng ka ho Sebelisa Mokhoa o sa Senyeheng, Felipe Gomes, Ph.D.seithuti, Univesithi ea McMaster
2:30-3 pm: 3D Characterization and Mechanical Analysis of Polyethylene Foams Sebetsa ka Rapid Rotational Foam Molding, Wing Yi Pao, Univesithi ea Ontario Institute of Technology
3-3:30 pm: Sebopeho sa 3D sa Boleng ba ho Tlamahanngoa ha Foam-to-Letlalo ho Rapid Rotationally Foam Molded Integral-Skin Cellular Composites
3:30-4 pm: Kalafo ea Bokaholimo ba Li-Agave Fibers le Tšebelisano ea Eona le PLA ho Hlahisa Li-Biocomposites tse Bopehileng ka Rotational, Jorge Robledo-Ortíz, Universidad de Guadalajara
4-4: 30 pm: Mechanical Characterization ea Polyethylene / Carbon Nanofiber Composites e Lokisitsoeng ke Rotational Molding, Milton Vazquez Lepe, Universidad de Guadalajara
4:30-5 pm: Ntlafatso ea Ts'ebetso ea Rotational Molding ea Agave Fiber / LMDPE Composite Materials, Pedro Ortega-Gudiño, Universidad de Guadalajara
5-5:30 pm: Morphology and Mechanical Properties of PLA Blends E hlahisitsoe ke Rotational Molding, Eduardo Ruiz Silva, Universidad de Guadalajara
5:30-6 pm: Rotational Molding of Hybrid Composites Based on Linear Low Density Polyethylene/Ground Tyre Rubber/Maple Wood Fibers, Denis Rodrigue, Université Laval
1:30-2 pm: Li-TPE tse Ncha tse Felletseng Likopong tse nang le Litlhoko tse Ikhethileng, Kushal Bahl, Teknor Apex Company.
2:30-3 pm: Synventive's New Synflow Technology e Lumella Molders Bokhoni bo Fetang ho Feta Pele ho Sebelisa Ho Tlatsoa ha Li-Cavities ka Phaketeng e Nchafatsoang, Greg Osborn, Synventive Molding Solutions.
4-4: 30 pm: Tsoelo-pele ho Fiber Laser Workstations for Plastic Welding Applications, Ben Campbell, Motlatsi oa Moprofesa oa Boenjiniere, Univesithi ea Robert Morris.
4:30-5 pm: Lits'enyehelo ho Theknoloji ea ho Welding ea Plastiki: Ho Chesa Gas Welding, Anthony Verdesca, Bielomatik Inc.
5-5:30 pm: Re Tsebisa STRIDE, Mokhoa o Kopanetsoeng oa ho Kopana le ho Kopanela R&D, Debora Massouda, Theknoloji ea Saense le Setsi sa Lipatlisiso sa Delaware (STRIDE)
10-10:30 am: Ho nepahala ha Dimensional le Malebela a Moralo bakeng sa Likarolo tse Kopantsoeng tse Entsoe ke Mokhoa oa FDM, Vittorio Jaker, Stratasys Inc.
8-9 am: Ntlha-kgolo: Ho Tlisa Dihlahiswa tsa Dihlahiswa tsa Temo Mmarakeng: Mathata le Menyetla, William Orts.
9-9:30 am: Thuto ea Biodegradable Polybutylene Succinate/Polybutylene adipate-co-terephthalate Blends, Feng Wu, Univesithi ea Guelph
9:30-10 am: Biodegradation of Biodegradable and Compostable Plastics Under Industrial Compost, Marine and Anaerobic Digestion, Joseph Greene, California State University, Chico
10-10:30 am: Tunable Degradation of Polybutylene succinate by Copolymerization and Catalysts, Siwen Bi, Ph.D.Seithuti, UMass Lowell
10:30-11 am: Mechanical Behaviour and Anaerobic Biodegradation of a PLA Blend Containing PLA-co-Polyglycolic acid Copolymer, Christopher Lewis, Rochester Institute of Technology
11-11: 30 am: Tharollo e tlase ea Mocheso oa Mocheso Depolymerization ea PLA, John Campanelli, Zeus Industrial Products
9-9:30 am: Tšusumetso ea Bonding Agents ka Fibermatrix Adhesion le Papiso ea VCF le RCF Fleece ho Epoxy Matrix, Jasmin Mankiewicz, Ph.D.seithuti, Univesithi ea Applied Sciences Niederrhein
9:30-10 am: Boithuto ba Teko mabapi le Karohano ea Fiber Matrix Nakong ea Compression Molding of Fiber-Reinforced Rib Structures, Christoph Kuhn, Volkswagen AG
10-10:30 am: Liphello tsa Li-Fillers tse fapaneng ho Thermomechanical Properties le Coefficient of Linear Thermal Expansion of Polypropylene Composites, Mohamed Abdelwahab, Univesithi ea Guelph
10:30-11 am: Inline UV Light Irradiation of Cellulose le Glass Fibers in Pultrusion of Thermoplastic Composites, Christian Kahl, Univesithi ea Kassel
11-11:30 am: Thepa Characterization of Injection Molded Hybrid Composites, Gangjian Guo, Univesithi ea Bradley
8-8:30 am: Quantitative Characterization and Modelling of Thin Film Conformability, Alexander Chudnovsky, Univesithi ea Illinois e Chicago.
8:30-9 am: Correlation of Chain Dynamics to Mechanical Properties of High-Performance Cross-Linked Systems, Shaw Hsu, Univesithi ea Massachusetts
9-9:30 am: Ho lelekisa Botlaaseng ba Sebaka sa Matla: Mouoane o Deposited Amorphous Fluorocarbons, Gregory McKenna, Texas Tech University
9:30-10 am: Ho Lemoha Mohloli oa ho Boloka Tire ka Innovative Tough Polymer Composite, Katsuhiko Tsunoda, Bridgestone Corp.
10-10:30 am: Ho utloisisa Boitšoaro ba Deformation ea Nanocomposites Ka Discrete Carbon Nanotubes, Clive Bosnyak, Molecular Rebar Design LLC
10:30-11 am: Quantitative Evaluation of Mar Visibility Resistance of Polymer Films, Shuang Xiao, Texas A&M University
11-11:30 am: Mechanical Characterization of Polycarbonate Reinforce With Woven Glass Fiber, Omar Solorza-Nicolas, Instituto Politecnico Nacional/Polimeros Y Compositos SA De CV
8-8:30 am: Ntlafatso ea Ts'ebetso ea Mokhathala oa Metal-Composite Friction Spot Joints Thehiloe ho Khopolo ea Weld-Bonding, Natalia Manente Andre, Helmholtz-Zentrum Geesthacht
8:30-9 AM: Direct-Friction Riveting of Metal-CFRP Overlap Joints, Natascha Zocoller Borba, Helmholtz-Zentrum Geesthacht
9-9:30 am: Adhesive-Free Bonding of Pine by Vibrational Welding, Curtis Covelli, Iowa State University
9:30-10 am: Patlisiso ea Teko ea Phetiso ea Amplitude ho Ultrasonic Welding of Thermoplastic Composites, Genevieve Palardy, Louisiana State University
10-10: 30 am: Boitšoaro ba ho Welding bo itšetlehileng ka Nako ea Foam Ente e Bopehileng Likarolo Tse Bopehileng ka ho Nahana ka Lintlafatso tse sa tšoaneng tsa Fiber le Mefuta e Kopanetsoeng, Dario Heidrich, Univesithi ea Theknoloji ea Chemnitz
10:30-11 am: Welding ea Infrared of Highly Filled Graphite Composites, Martin Facklam, Institute for Plastic Processing
11-11:30 am: Welding ea Infrared of Continuous Glass-Fiber-Reinforced Thermoplastics: Mekhoa ea ho Sebelisa Lithaele tse Kopantsoeng, Marios Constantinou, Univesithi ea Theknoloji ea Chemnitz
8-11:30 am: Keynote: Litlhahiso ho Phekolo ea Plastiki bakeng sa Likopo tsa Tlhokomelo ea Bophelo, Manish Nandi, Sabic
8:30-9 am: Keynote: Nts'etsopele le Mekhoa e Mecha ho Extrusion ea Bongaka, Steve Maxson, Graham Engineering
9-9:30 am: Laser-based Processing of Polymers for Medical Application, Roger Narayan, NC State University
9:30-10 am: Micromolding Drug Delivery Devices ho Micron Tolerances, Donna Bibber, Isometric Micro Molding Inc.
10-11:30 am: Puisano ea Panel: Ntlafatso ea Karolo ea Ts'ebetso le netefatso ea Mechini e Mengata, Matthew Therrien, Rod Brown, Greg Lusardi, Paul Robinson, Brad Smith, Ed Valley, Scott Scully
8-8:30 am: Keynote: Phello ea Mouoane oa Metsi ho Thermal le Mechanical Properties ea Amphiphilic Block Copolymer Membrane, Daniel Hallinan, Florida A&M University le Florida State University College of Engineering
8:30-9 am: Patlisiso ea Mocheso Pakeng Tsa Khatello ea Khatello le Thermal Annealing Lithutong tsa Botsofali tsa Glassy Thermosets, Brendan Ondra, Univesithi ea Massachusetts–Amherst
9-9:30 am: Ho Shebehile Phallo ea Particle Nakong ea Ts'ebetso ea Polypropylene ka Lifaha tsa Khalase, Jose Luis Colon Quintana, UW-Madison
9:30-10 am: Karolo ea ho sebetsa ha Nanoclay Particles on Diffusion Properties of Commercial Gasoline through Polymer Membranes, James Sloan, US Army Research Laboratory.
10-10: 30 am: Tlhaloso ea Tlhahlobo ea Lihlahisoa tsa Khoebo: Cool Comfort Technologies bakeng sa Lihlahisoa tsa Libethe, Praveenkumar Boopalachandran, Associate Research Scientist, Dow Chemical Co.
10:30-11 am: TGA-FTIR E Lokolohile Qetellong: E Tseba Khokahano e Kopantsoeng ka Botlalo, e sa Fetisetsoang Mahala bakeng sa Tlhahlobo ea Khase e Evolved ea Polymers, Bob Fidler, NETZSCH Instruments NA LLC.
11-11:30 am: Polyetheretherketone (PEEK) Ho pepesetsoa Fluids ea Qetelo ea ZnBr2 ka Lithempereichara tse Holimo le Khatello: Ho Khetholla le ho Lekanya Lihlahisoa tse Nyenyane tsa ho Senyeha ha Limolek'hule, Joseph Baker, Texas A&M University
8-8:30 am: Keynote: Stress-Induced Crystallization in Polypropylene, Pierre Donaldson, Flint Hills Resources
9:30-10 am: Particle Additives for Simltaneous Enhancement of Degradation and Toughening in PLA for Additive Manufacturing, Caroline Multari, Univesithi ea Lehigh
10-10:30 am: A Characterization of Soy Additives in Bio-based Polyethylene Films, Peter Perez, UMass Lowell
2:30-3 pm: Tlhahiso ea'Z' Aligned Ultrasensitive, Flexible and Transparent Piezoelectric Nanocomposites, Mukerrem Cakmak, Univesithi ea Purdue
1:30-2 pm: Keynote: Moralo, Moenjiniere, Teko, 3D Print for Production - In That Order, Albert McGovern, Shure Inc.
2-2:30 pm: 3 Kelello ea Hao: Ho Printa Kapa Ho se Hatise, Eo ke Potso e Ekelitsoeng ea Tlhahiso, Jim Allen, 3YOURMIND
3-3:30 pm: Phaliso e Sebetsang Pele ho Tlhahiso e Kenyellelitsoeng: Art of Leveraging Constraints, Ravi Kunju, Altair
3:30-4 pm: Mekhoa e Molemo ka ho Fetisisa ea Moralo oa Likarolo Tse Hatisitsoeng tsa Plastic 3D, Ashley Eckhoff, Siemens PLM Software.
4:30-5 pm: Ho netefatsa ho ts'epaha ha Mechini ea Likarolo tse Eketsehileng ka Teko le Papiso, Mark Oliver, Veryst Engineering.
5-5:30 pm: 3Degrees: Mokhoa oa ho Atamela ho netefatsoa ha lintho bakeng sa likarolo tsa tlhahiso, Mike Vasquez, 3Degrees
2-2:30 pm: Phello ea Keketso ea Letsoai ho Dynamic Mechanical Properties bakeng sa Polymethyl methacrylate, Masayuki Yamaguchi, Japan Advanced Institute of Science and Technology
2:30-3 pm: Synergistic Acsorption of Microwave Radiation in PVDF Hybrid Nanocomposites E Nang le Multiwall Carbon Nanotubes le Ferrite Particles, Uttandaraman Sundararaj, Univesithi ea Calgary
3:30-4 pm: Rheology e le Sesebelisoa sa ho Utloisisa Thepa ea Antidrip ka har'a Flame-Retardant Polycarbonate Resins, Manojkumar Chellamuthu, Sabic
4-4:30 pm: Nonlinear Viscoelastic Fluid Models With Fractal Time Derivative, Donggang Yao, Georgia Institute of Technology
4:30-5 pm: Polelo ea Boima ba Limolek'hule ea Rheology Khahlanong le Gel Permeation Chromatography bakeng sa Film Grade Polypropylene, Hoda Bayazian, Univesithi ea Paderborn, Jeremane.
5-5:30 pm: Phello ea Boima ba Limolek'hule ho Dynamics of Linear Isotactic Polypropylene Melt at Very High Shear Rates, Martin Zatloukal, Tomas Bata University e Zlin
5:30-6 pm: Tšusumetso ea Maholimo a Oscillating ho Rheological Behavior of Thermoplastic Melt, Julius Geis, TU Ilmenau
2-2:30 pm: Nako ea ho Qhibiliha le ho Lula ka Sekheong se le Mong sa Extrusion, Clemens Martin Grosskopf, Univesithi ea Applied Sciences, Darmstadt, Jeremane.
2:30-3 pm: A Network Analysis-Thehed Comparative Study of the throughput Behavior in Double Wave Screw Geometries, Hans-Juergen Luger, Institute of Polymer Extrusion and Compounding
3-3: 30 pm: Tšebeliso ea Khatello le Boemo ba Mocheso ka hare ho Extruder bakeng sa Ntlafatsa / Troubleshooting Extrusion Processes, John WS Lee, LS Cable & System
3:30-4 pm: Tlhahlobo ea Litšenyehelo bakeng sa ho Kenya Li-Screw tse Ncha le tse Lokisitsoeng bakeng sa Lithapo tsa Single-Screw Extrusion, Mark A. Spalding, Dow Chemical Co.
4-4:30 pm: Tlhahlobo e Bonolo ea Sistimi bakeng sa Small Extrusion Screw and Die, Jingyi Xu, Graham Engineering Corp.
4:30-5 pm: Tlhahlobo ea Tšebeliso ea Matla ho Melt Spinning: Mono le Bi-Component Fibers, Javier Vera Sorroche, UMass Lowell
5-5: 30 pm: Patlisiso ka Liphello tsa Mekhahlelo ea Ts'ebetso ho Boleng ba Replication ea Microstructures ka Extrusion Embossing ea Polycarbonate Films, Florian Petzinka, Institute of Plastics Processing
5:30-6 pm: Phello ea Scale Up on Thermal Homogeneity and Energy Efficiency in Single-Screw Extrusion, Javier Vera Sorroche, UMass Lowell
1:30-2:30 pm: Keynote: Tan Delta: Thepa e se Nang Dimension E U Bolellang Tsohle Seo U Lokelang ho se Tseba ka Polymeric Material, Michael Sepe, Michael P. Sepe LLC
2:30-3 pm: Fractography: Saense le Art ea ho Fumana Hore na Plastiki e Senyeha Joang, Farzana Ansari, Exponent
3-3:30 pm: Tlhahlobo ea ho Hloka ho Sebelisa FT-IR le Raman Microspectroscopy, Rui Chen, Thermo Fisher Scientific
3:30-4 pm: Mokhoa oa ho Sebelisa Mekhoa ea Thermoanalytical bakeng sa Tlhahlobo ea Ho hloleha, Tobias Pflock, NETZSCH-Gerätebau
4-4: 30 thapama: Patlisiso ea Phello ea Sisteme ea Stabilizer, Medium le Mocheso ho Khanyetsano ea Khōlo ea Mokhathala oa Crack ea Polypropylene bakeng sa Khetho e nepahetseng ea Lintho, Jorg Fischer, Johannes Kepler University Linz, Setsi sa Lisebelisoa tsa Polymeric le Teko.
4:30-5 pm: Thepa ea Fracture ea HDPE e Hlahisitsoe ho Metsi a Chlorinated, Susan Mantell, Univesithi ea Minnesota
5-5:30 pm: Ho hanela Mokhathala le ho Hloka Boitšoaro ba Glass-Fiber-Reinforced PA Grades, Patrick R. Bradler, Johannes Kepler University Linz, Institute of Polymeric Materials and Testing
5:30-6 pm: Raman Spectroscopic Fumaneha ea Liphetoho tse nyenyane tsa Sebopeho sa Polyethylene Nakong ea Phokotso ea Photodegradation, Yusuke Hiejima, Univesithi ea Kanazawa.
6-6:30 pm: Mathata leha e le afe a Bulging kapa Paneling bakeng sa Liphutheloana tsa Hau?, Jay Yuan, Stress Engineering Services Inc.
1:30-2 pm: Keynote: Polyolefin Elastomers: Material Science and End Use Application, Seema Karande, Dow Chemical Co.
2-2:30 thapama: Mekhoa ea Rheological ea ho Hlahisa Boemo ba Lekala la Long Chain ka Polyethylene, Greg Kamykowski, SPE
3-3:30 pm: Phello ea HNTs Dispersion in PVDF on Morphology and Its Formation Mechanism of Tensile Fractures Surfaces, Han-xiong Huang, South China University of Technology
3:30-4 thapama: Boikemisetso ba Lisebelisoa tse Khanyang Lelakabe ka Lipolasetiki tse Sebelisang Motsoako oa Mekhoa ea Tlhahlobo, Yanika Schneider, EAG
4-4:30 pm: Open-Cell Foaming of PP/PTFE Fibrillated Composites, Yu Guang Chen, Univesithi ea Toronto
4:30-5 pm: Core/Shell Structure of Electrospun Polycarbonate Nanofibers, Yiyang Xu, Univesithi ea Wisconsin-Madison
5-5: 30 pm: Liphello tsa Li-additives tsa Biodegradable Additives ho Nucleation Intensity le Growth Rate ea Isotactic Polypropylene Spherulites, Yousef Mubarak, Univesithi ea Jordan
5:30-6 pm: Sehlopha sa Pellet Shape Ho Sebelisa Deep Neural Networks, Brenda Colegrove, Dow Chemical Co.
3-4 pm: Kamoo Boenjiniere ba Lerako bo Amang Bokhoni ba Ts'ebetso le Matla a Ts'ebetso, Suhas Kulkarni, FimmTech Inc.
4-5 pm: Kamoo Moralo o Fosahetseng o ka Lekanyetsang Lisebelisuoa, Lisebelisuoa le Matla a Ts'ebetso, Vikram Bhargava, Sengoli, Mokoetlisi le Moeletsi.
5-6 pm: Phello ea Mould ea Mocheso o Potlakileng ho Thepa ea Lintho tse Thehiloeng ka Polycarbonate, Jessica Boyer, Covestro LLC
1:30-2 pm: Ntlafatsa Ts'ebetso ea Filimi ea Hao ea Retort Flexible, Sergi Salva Saez, UBE America Inc.
2-2:30 pm: Thermally Purified Carbons for Food Contact Applications: Taba ea Boithuto ba Tumellano ea EU, Rijo Jacob Robin, Superior Graphite
2:30-3 pm: Lik'hemik'hale tsa Biopolymer bakeng sa Likopo tse Hlokang ho Senngoa ha Leoatle, Stanley Dudek, Polymer Processing Tech LLC.
3-3:30 pm: Likopo tsa Novel tsa Beta Nucleated Polypropylene ho Filimi, Thermoforming le Ente Likopo tsa Molding, Philip Jacoby, Jacoby Polymer Consulting.
4-4:30 pm: Schulamid High-Performance Nylon for Fuel System Applications, Ying Shi, A. Schulman Inc.
5-5:30 pm: Nanolayered Next Generation High-Energy Density Capacitors bakeng sa Likoloi tsa Motlakase, Michel Ponting, PolymerPlus LLC
4-4:30 pm: Laser Welding Plastics: Rapid Prototyping to Mass Production Ho Sebelisa Quasi-Simultaneous le 2D/3D Mask Welding, Andrew Geiger, Leister Technologies
4:30-5 pm: Melemo ea Vibration Welding With IR Preheat, John Paul Kurpiewski, Emerson - Branson
6-6: 30 pm: Ultrasonic Welding 20 kHz vs. 15 kHz: Mathata a hlahisitsoeng ke Highly Crystalline Material, Dave Krysiak, Sonics & Materials
8:30-9 am: Likamano tsa Mohaho-Mohaho oa Membrane ea Microporous E Hlahisoa ke Biaxial Orientation of Compatibilized PP/Nylon 6 Blends, Jingxing Feng, Ph.D.seithuti, Univesithi ea Case Western Reserve
9-9:30 am: Patlisiso ea Boits'oaro ba Droplet Tlas'a Maemo a 'Nete a Ho Kopanya, Oguz Celik, Institut für Kunststofftechnik-Univesithi ea Stuttgart
9:30-10 am: Tšusumetso ea Ts'ebetso le Tlhahiso ho Thepa ea PP-PET-Blends, Christoph Burgstaller, TCKT
10-10:30 am: Nylon 12/PMMA/San Alloys for Translucent Medical Catheters, Timothy Largier, Foster Corp.
10:30-11 am: Moralo oa Extensional Flow Static Mixers bakeng sa ho Kopanya Ternary Nanoparticle-Polymer-Polymer Blends, Matthew Thompson, Toray Composite Materials America Inc.
11-11:30 am: Keynote: Biopolymer Alloys and Blends: Nako E Fetileng, Hona Joale le Bokamoso, Roger Avakian, PolyOne Corp.
8-8:30 am: Litlhahiso ho Plastiki ea Likoloi "Lisebelisoa le Mekhoa," Suresh Shah, Delphi Corp. (O tlohetse mosebetsi)
9-9:30 am: Low Birefringent Cellulose Acetate Propionates for Plastic Display Lens Covers, Laura Weaver, Eastman Chemical Co.
9:30-10 am: Selelekela sa Tšebeliso ea Thermally Conductive Compounds in Automotive Lighting, Paula Kruger, DSM.
10-10:30 am: Resin e Ncha bakeng sa Li-module tse Fokolitsoeng tsa Mokelikeli ka har'a Lipakete tsa Battery tsa Koloi ea Motlakase, Rudy Gorny, Covestro LLC
10:30-11 am: Ho Ntlafatsa Khahlano ea Nako e Telele ea Corrosion ho Lisebelisoa tsa Elektronike, Josh McIlvaine, DuPont Co.
11-11: 30 am: Tsoelo-pele ho Hydrolysis Resistance PBT Resins bakeng sa Likopo tsa Elektronike tse kenyeletsang li-Connectors le HEV Components, Dave Spritzer, DuPont Co.
8-8:30 am: Nts'etsopele ea Theknoloji ea Mold Molding e potlakileng ea Thermal Cycling le Optimization ea Mold Heating System, Cheng-Long Xiao, Univesithi ea South China.
8:30-9 am: Simulative Preform Optimization for Improved Topload Behaviour of PET Bottles E Entsoe ka Two Stage Stretch Blow Molding Process, Benjamin Twardowski, IKV Aachen
9:30-10 am: Moralo oa Ketsiso bakeng sa ho Bopa ha Leqhubu: Thuto- Nyeoe ea Pele mabapi le Ente e otlolohileng ea ho Bula bakeng sa Likoahelo tsa Bulb, Raghavendra Janiwarad, Sabic
10-10: 30 am: Numerical Simulation of Shrinkage le Warpage Deformation ea Intermittent-Extrusion Blow Molded Part: Validation Case Study, Zohir Benrabah, National Research Council Canada
8-8:30 am: Foam Structure and Thermal Comfort in Polyurethane Mattress Foams, Douglas Brune, Dow Chemical Co.
8:30-9 am: Polelo-pele ea Fiber-Reinforced Plastics Ho Nahana ka Bolelele ba Fiber ea Lehae le Orientation, Fabian Willems, Institut für Kunststofftechnik
9-9:30 am: Ketsiso e Sebetsang ea Liquid Crystal Polymer Directionality nakong ea Ts'ebetso, Anthony Sullivan, Univesithi ea Tufts
9:30-10 am: Crystallization Mechanism of Polyvinylidene Fluoride via Nonisothermal Crystallization and Supercritical CO2 Processing, Ji Eun Lee, Univesithi ea York
10-10: 30 am: Macromolecular Spectroscopy bakeng sa ho Khetholla Mechanical Properties ea Polydimethylsiloxane (PDMS), Ahmed Anwer, Univesithi ea Toronto
10:30-11 am: Mathata a Phallo a ka Hlahang ho Tsoa ho Kenyeng Lisebelisuoa tsa Biomass ho Plastics, Carrie Hartford, Jenike & Johanson
11-11:30 hoseng: Mekhoa ea Rotomolding Bakeng sa Polyaryl Ketones Le Li-polymers tse ling tse Phahameng tsa Mocheso o Phahameng, Manuel Garcia-Leiner, Exponent
8-8:30 am: Lintlafatso tse Tsoelang Pele ho Ts'ebetsong ea Semicrystalline le Amorphous Polymers bakeng sa Letlapa la Thermoforming ho Multiple Nip Systems, Peter Rieg, Battenfeld-Cincinnati
8:30-9 am: Effect of Die Exit Stress State, Deborah Number le Extensional Rheology on Neck-In Phenomenon, Martin Zatloukal, Tomas Bata University e Zlin
9-9:30 am: Microlayered Tubing and Pipes via Multilayer Coextrusion, Tyler Schneider, Case Western Reserve University
9:30-10 am: Karolo ea Interfacial Crystallization ho Rala Polyolefin Blends From Mixed Stream Recycle Feeds, Alex Jordan, University of Minnesota
10-10: 30 am: Tlhahlobo ea Thermoplastic Polyurethane (TPU) Resins e le Lintho Tse ka Etsahalang Bakeng sa Li-Resins tsa Hona Joale bakeng sa Escalator Handrails, Qingping Guo, EHC Canada
10:30-11 am: Thuto ea Pele ea Kabo ea Birefringence ho Blown Film, Jin Wang, Dow Chemical Co.
11-11:30 am: Energy Gap Method (EGM) E Sebelisoa ho Ntlafatsa Ts'ebetso ea Matla a Extrusion: Lithuto tse Atlehileng, Juan Carlos Ortiz Pimienta, ICIPC (Instituto de Capacitación e Investigación del Plástico y del Caucho)
9:30-10 am: Poly Vinylidene Fluoride/ Graphene Nanoplatelets Composites Ka Sebopeho sa Microcellular ho Ntlafatsa Thepa ea Tšireletso ea Motlakase, Biao Zhao, Univesithi ea Toronto
10-10:30 am: Ho Matlafatsa Ts'ebetso ea Ts'ireletso ea Motlakase ea Likopano tsa PVDF/MWCNT Ka Ho Foaming, Chenyinxia Zuo, Univesithi ea Toronto ea seithuti
10:30-11 am: Foams Piezoelectric With High Thermal Stability and Flexibility, Zhe Liu, Florida State University
11-11: 30 am: Resorcinol Formaldehyde Airgel Nanonetwork Structural Assembly le Thermal Properties Correlation, Mohammed Alshrah, Univesithi ea Toronto
8:30-9 am: Theknoloji e Ncha ea Ntlafatso ea Ts'ebetso ea Halogen-Free Flame-Retardant ho Polymer Application, Ido Offenbach, Evonik
9-9:30 am: New Generation Flame Retardants Based on Ionic Liquids, Yanjie "Jeff" Xu, Inovia Materials LLC
9:30-10 am: Mokhoa oa Novel oa ho falla ho laolehileng ha Antifog Additives ho Multilayer Packaging Films, Michal Schreiber, Tosaf
10-10:30 am: Novel Dispersants E Nobled by Natural Oil Metathesis, Frederyk Ngantung, Elevance Renewable Sciences
11:30 am-12 pm: Ntlafatso ea Bokaholimo ka Polypropylene Metallic Compounds, Tanmay Pathak, A. Schulman Inc.
8:30-9 am: Keynote: Moetso oa Phetisetso ea Mocheso ka Lifilimi tse ngata tsa Multilayer tse Sebelisitsoeng bakeng sa ho Packaging ka Flexible, Dan Ward, NOVA Chemicals
9-9:30 am: Thermo-Rheological Modelling and Simulation of Heat Tiling Process for Multilayer Flexible Packaging Application, Vinod Kumar Konaganti, Nova Chemicals Corp.
9:30-10 am: Lisebelisuoa tsa Barrier tse nang le Lera-Joaloka Morphology bakeng sa Tšebeliso ea Liphutheloana: Filimi e Atolositsoeng le Filimi e Lebeletsoeng, Guojun Zhang, A. Schulman Inc.
10-10:30 am: Keynote: Ho Fetola Matla a 'Maraka le Maemo a TPE bakeng sa Phaello ea Bokamoso, Phapang le Kholo, Robert Eller, Robert Eller Associates LLC
10:30-11 am: Elastic Recovery and Actuation In Polyolefin Thermoplastic Elastomers, Barbara DeButts, Virginia Tech
11-11:30 am: Ho Tloha ho Lithaere tse Recycled ho ea Likarolong tsa Plastiki: Li-Micronized Recycled Rubbers in Thermoplasitc Polyolefins, Haikun Xu, Entech Inc.
1:30-2 pm: Tharollo ea Foromo e Koetsoeng bakeng sa ho Bolela Karolo ea ho Qetela Matla a Fused Deposition Modeling, Steven Devlin, Univesithi ea Missouri.
2:30-3 pm: Characterization and Mechanical Behaviour of SLS Processed PA11/CB Nanocomposites, Gabrielle Esposito, seithuti se fumaneng mangolo, Univesithi ea Lehigh
3-3:30 pm: Tšusumetso ea Ts'ebetso ea Elliptic Smoothness le Powder Shape Factors on Additive Manufacturing With Laser Sintering, Marc Vetterli, Inspire AG ICAMS
3:30-4 pm: The Basic Characterization of CLIP 3D Printed Materials, Danielle Grolman, United Technologies Research Center
4:30-5 pm: Patlisiso ea Novel Additive Manufacturing Technique "4D-RheoPrinting" bakeng sa Tlhahiso ea Lihlahisoa tse Matlafalitsoeng tsa Polymeric, Alaauldeen Duhduh, Ph.D.seithuti, Univesithi ea Lehigh
5-5:30 pm: Nomoro ea Bohlokoa ea Capillary ho Hyperbolic Converging Nozzle for Polymer-based Additive Manufacturing, Aditya Sangli, Univesithi ea Maryland, College Park.
5:30-6 pm: Khetho ea Lintho, Ho Lekoa le ho Tiisoa ha Likarolo Tse Ekelitsoeng Tse Eketsehileng, Johannes Wiener, Montanuniversitaet Leoben
6:30-7 pm: Patlisiso ea Khetho ea Laser Sintering Parameters mabapi le Tensile Properties ea Polyamide 11, Gabrielle Esposito, seithuti se fumaneng mangolo, Univesithi ea Lehigh.
2-2:30 pm: Phetoho ea Thepa ea Rheological le Crystallization of High-Performance Polymers bakeng sa Likopo tsa Thermoplastic Composite, Sarah Morgan, Univesithi ea Southern Mississippi
2:30-3 pm: Patlisiso mabapi le Viscosity Characterization of the Glass Mat Thermoplastics (GMT) in Compression Molding System, Chien Tse-Yu, Tamkang University
3-3:30 pm: Ponahalo ea Litsela Tse Phallang ho Motsoako oa ka Hare oa Tangential ho Ntlafatsa Boitšoaro ba ho Kopanya, Annika Lipski, Setsi sa Ts'ebetso ea Plastic ho Indasteri le Mesebetsi ea Mesebetsi Univesithing ea Theknoloji ea Aachen.
3:30-4 pm: Liphello tsa Metal Stearates ho Rheological Properties of Powder Injection Molding Feedstocks le Litholoana tse Molded Green, Michael Shone, UMass Lowell.
4-4:30 thapama: Tlhahlobo ea Root Cause ea Polyolefin-Based Wire le Cable Formulation Die Build-Up, Kurt Koppi, Dow Chemical Co.
4:30-5 pm: Ntlafatso ea Mokhoa oa Rheological: Meetso ea Polymer bakeng sa Blow Molded, Litulo tsa Likoloi, Mary Ann Jones, Dow Chemical Co.
5-5:30 pm: Bohlokoa ba Hore na Li-Rheometers Tsa Marang-rang li Bontša Ka nepo Sekhahla sa Melt Flow ho Extruder, Catherine Lindquist, Dynisco
5:30-6 pm: Mohlala oa Mechanist bakeng sa ho Tlatsa Nanocavity, Donggang Yao, Georgia Institute of Technology
1:30-2 pm: Ntlafatso ea Ts'ebetso ea Thermal ka ho Otlolla Polyethylene-Graphene Nanocomposites, Brian Grady, Univesithi ea Oklahoma.
2-2:30 pm: Ts'ebetso ea Parameters Phello ho Barrier Properties ea Nitrile-Based Nanocomposite Membrane, Mohamed Zemzem, Ph.D.seithuti, École de Technologie Supérieure
2:30-3 pm: Litšobotsi tsa Boits'oaro ba Scratch of Multilayer Automotive Coatings for Various Scratch Conditions, Sung Wook Moon, Univesithi ea Korea.
3-3:30 pm: Biomimetic Nanocoatings Ka Mechini e Ikhethang, Barrier le Thepa e Retang Lelakabe ho Tsoa ho Large Scale One-Moto Coassembly, Luyi Sun, University of Connecticut.
3:30-4 pm: Mehaho ea Sebopeho sa Micro- Le Nano-Layer le Thepa ea Tsona ea Tšebetso ea Polymers, Shaoyun Guo, Polymer Research Institute ea Sichuan University.
4-4:30 p.m
4:30-5 pm: Membrane ea Filimi ea Microcapillary e Thehiloe ho Polyvinylidene Fluoride, Gerald Billovits, Dow Chemical Co.
5-5:30 pm: Numerical Modelling of Complex Parison and Sheet Formation in Blow Molding Processs using BlowView Software, Zohir Benrabah, National Research Council Canada
5:30-6 pm: Kamoo Polymer Rheology e Amang Ts'ebetso ea Extrusion Blow Molding, Todd Hogan, Dow Chemical Co.
6-6:30 pm: Synergistic Reinforcing le Toughening High Density Polyethylene ka ho Hlahisa Dynamic Shear Force Field le Ultrahigh Molecular Weight Polyethylene, Tong Liu, South China University of Technology
6:30-7 pm: Liphello tsa Extruder Screw Configuration ho Thermal Properties of Glass-Fiber-Reinforced Polyamide 6 Composites Ho pholletsa le Ts'ebetso e Otlolohileng ea Thermoplastics ea Long-Fiber-Reinforced Thermoplastics, Takashi Kuboki, Univesithi ea Western Ontario.
1:30-2 pm: Ketsiso e Kopanetsoeng ea Phallo ea Extrudate Ka lebaka la Nonuniform Exit Velocity le Cooling Shrinkage, Mahesh Gupta, Phallo ea polasetiki
2-2:30 pm: Ho Etsa Mohlala oa Mokhoa o Bonolo oa Numerical Calculation Methodology to Kempling Cross Flows in Extrusion Die Design E Thehiloe ho Theory Network, Bianka Jacobkersting, University of Paderborn
2:30-3 pm: Ho Etsa Mohlala oa Boitšoaro ba Tšilafalo ea Li-Filters tsa Polymer Melt le Litšoantšiso tsa Tahlehelo ea Khatello ea Filtration Media, Volker Schöppner, Univesithi ea Paderborn.
3-3:30 pm: Boithuto ba Teko mabapi le Melt Encapsulation: Analysis of Die Pressure le Rearrangement Effects, Christian Hopmann, Institute of Plastics Processing (IKV) in Industry le Skilled Crafts at RWTH Aachen University.
3:30-4 pm: Phello ea Channel Curvature ho Phallo Rate le Viscous Dissipation ea Power-Law Fluids, Wolfgang Roland, Institute of Polymer Extrusion and Compounding
4-4:30 pm: A Heuristic Model bakeng sa ho bolela esale pele Phallo ea Maemo a mararo a sa Newton ka Metering Channels, Christian Marschik, Institute of Polymer Extrusion and Compounding
4:30-5 pm: Ho etsa mohlala oa Ts'ebetso ea Ts'ebetso ea Melt Filtration ho Polymer Recycling, Sophie Pachner, Institute of Polymer Extrusion and Compounding
1:30-2 pm: Tlhahlobo e Ikemetseng ea Anomaly le Sesosa sa Motso bakeng sa Tlhokomelo le Taolo ea Ts'ebetso ea Holistic ho Molding ea Ente, Alexander Schulze Struchtrup, Univesithi ea Duisburg-Essen
2-2:30 pm: Boitšoaro ba Inflation of Preforms in the Special Ente Molding Process GITBlow Combining Molding ea Ente e Thusang ka Khase le Mould Molding, Björn Landgräber, Univesithi ea Paderborn
2:30-3 pm: Phello ea Boemo ba Ente ea Mould ka Mould Adhesion during Thermoplastic Polyurethane Entection Molding, Jian-Yu Chen, Feng Chia University
3-3:30 pm: Ho tsitsisa ha BMC Ente Molding ka Mehato ea Taolo ea Ts'ebetso, Nicolina Topic, KraussMaffei Technologies GmbH
3:30-4 pm: Tlhahiso ea Zero Defect ka Ente ea Compression Molding ea Polymer Fresnel Lenses, Dario Loaldi, Technical University of Denmark
4-4:30 thapama: 3D Surface Characterization of Etched, Ente e bōpiloeng ka likarolo Pele ho Ts'ebetso ea ho Latela Electroplating, Jens P. Siepmann, Univesithi ea Duisburg-Essen
4:30-5 pm: Multilayer Injection Molding of Thick-Walled Optics Ho Sebelisa Matla a Mold Tempering le Optimized Layer Thickness Distribution, Malte Röbig, Institute of Plastics Processing (IKV) indastering le litsebi tsa mesebetsi ea matsoho Univesithing ea RWTH Aachen.
5-5:30 pm: Ho Sebelisa Magneto-Archimedes Levitation Bakeng sa Sebopeho se sa Hlaseheng sa Likarolo Tse Mold ea Ente, Peng Zhao, Univesithi ea Zhejiang
5: 30-6 pm: Netefatso ea Mokhoa oa Numerical le o Sebetsang ho Kenyeng Ts'ebetsong Matlotlo a PVT a Polymer ho Laola ho Laola Boleng ba Shrinkage ea Molded, Tzu-Hsiang Wei, Ph.D.seithuti, Chung Yuan Christian University
1:30-2 pm: Ntlha ea bohlokoa: Ntlafatso ea Ts'ebetso ea Tubing ea Bongaka Ka Simulation, John Perdikoulias, Compuplast International Inc.
2-2:30 pm: Systems Engineering bakeng sa Ntlafatso ea Lisebelisoa tsa Bongaka: Kopo ea Lipompo tsa Insulin, Marc Horner, Ansys Inc.
2:30-3 pm: Liphello tsa Tikoloho ea Baeloji ho Thermoplastic Polyurethanes, Ajay Padsalgikar, Abbott
3-3:30 pm: Accounting bakeng sa Phapang ea Modulus le Stress Relaxation Behaviour in Plastics E Etsang Teko ea ho hanyetsa Lik'hemik'hale, Mark Yeager, Covestro LLC
3:30-4 pm The Degradation Products of Medical Devices in Complex Biological Environments: Risk Assessment Strategies, Adam Kozak, Cambridge Polymer Group.
4-4: 30 pm: Botsofali bo Potlakileng ba Mekhatlo ea Bongaka: Lintlha tsa Q10 le Mehlala ea Botsofali ba Lintho, Rob Klein, Litšebeletso tsa Boenjiniere ba Khatello
4:30-5 pm: Libaka tse Enjenetsoeng tsa Polymer bakeng sa Ts'ebetso e Ntle ho Likopo tsa Meriana, Prakash Iyer, Inhance Technologies.
5-5:30 pm: Supercritical Carbon Dioxide Assisted Extrusion of Graphene Nanofiller Reinforced Polymers for Biomedical Applications, Austin Coffey, Waterford Institute of Technology
5:30-6 pm: The Regulation of Micro-Super-Hydrophobic Silicone Rubber to the Behavior of Human Lens Epithelial Cells, Liuxueying Zhong, State Key Laboratory of Ophthalmology, Zhongshan Ophthalmic Center, Sun Yat-sen University, Guangzhou
2-2:30 pm: Lintlha tse Potlakileng tsa Boemo ba Leholimo ho Asa Polymer UV Resistance: Xenon vs. Quv vs. Florida And Arizona, Steven Blazey, A. Schulman Inc.
2:30-3 pm: Bohlokoa ba Hore na Li-Rheometers Tsa Marang-rang li Bontša Ka nepo Sekhahla sa Melt Flow ho Extruder, Catherine Lindquist, Dynisco
3-3: 30 pm: Characterization of Cure of Polymeric Material by Dielectric Analysis (DEA), Yanxi Zhang, Netzsch Instruments North America LLC
4-4:30 thapama: Leveraging Advanced Edge Analytics bakeng sa Ntlafatso ea Phoso e Ntlafetseng ho Mekhoa ea Tlhahiso ea Discrete, Andrew Wilson, MKS Instruments Inc.
5-5:30 pm: 3D Line Confocal Imaging: Theknoloji e Ncha ea High-Resolution Sensor bakeng sa Likopo tsa Melaho ea Plastiki e Fehlang Inthaneteng le e sa Keneng Inthaneteng, Juha Saily, FocalSpec Inc.
1:30-2 pm: Ho ea ho Ontology e Bonolo: Carbon to Building, Mark Goulthorpe, Massachusetts Institute of Technology
2-2:30 pm: Ho Finyella Khoutu ea Kaho ea Machabeng Kamohelo ea Lisebelisoa tsa Kaho tsa Polymeric: Litlhoko tsa Ts'ebetso ea Mollo, Nicholas Dempsey, Worcester Polytechnic Institute.
2:30-3 pm: Ho Rala Bakeng sa Tšireletseho ea Mollo: Litlhokomelo bakeng sa Ntšetso-pele ea Sehlahisoa, Christine Lukas, Dow Chemical Co.
3-3:30 pm: Ho Leba Moqapi o Bohlale oa Lihlahisoa tse Sireletsehileng tsa Mollo oa Polymeric, Stanislav Stoliarov, Univesithi ea Maryland
3:30-4 pm: Likarolo tse Matlafalitsoeng tsa Polymer bakeng sa Meralo ea Sechaba, Hota Gangarao, Univesithi ea West Virginia
4-4:30 p.m
4:30-5:30 pm: Keynote: Design Knock-Down Factors on Polymer Composites Tlas'a Tikoloho e Hare, Hota Gangarao, Univesithi ea West Virginia
6-6: 30 pm: Corrosion Inhibition Model bakeng sa Aluminium ka Sodium Carboxymethyl Cellulose (Polymer) In Acidic Solution, Macdenis Egbuhuzor, Univesithi ea Nigeria Nsukka
8-8: 30 am: Mohato o le Mong oa Phekolo ea Electrochemical ea Metal Inserts bakeng sa Likopo tse Tight Polymer-Metal Hybrid, Tobias Kleffel, Setsi sa Polymer Technology
8:30-9 am: Liphello tsa Ts'ebetso ea Liphetoho ho Mekhahlelo ea Crystallization ea PVDF-TRFE-CFE Thin Films, Hao Pan, UMass-Lowell
9-9:30 am: Litlhapi tse Ncha tsa Transparent High-Heat Polycarbonate Copolymer bakeng sa Lisebelisoa tsa Thermo-Optical, Mark Van Der Mee, Sabic
10-10:30 am: Biochar e Tlatsitsoeng Haholo/Ultrahigh Molecular Weight Polyethylene/Linear Low Density Polyethylene Composites for Electromagnetic Interference Shielding, Suiyi Li, University of Wisconsin--Madison
10:30-11 am: Thermoelectric Properties of Open Cellular Polymer Templates Coated With 1D le 2D Carbon-based Nanoparticles, Siu Ning (Sunny) Leung, York University
7:30-8 am: Tšenyo e Bakiloeng ke Tšebeliso ea Bokaholimo ba Lisebelisuoa tse Kopantsoeng tsa Fiber PDMS, Reza Rizvi, Univesithi ea Toledo
8-8: 30 am: Tšusumetso ea Botsofali ba Hygrothermal ho Thepa ea Material of Endless Fiber-Reinforced Thermoplastics, Matthias Huettner, Univesithi ea Paderborn
8:30-9 am: Tšusumetso ea Tšebelisano-'moho ea Fiber-Matrix ka Boitšoaro ba Fracture ea Regenerated Cellulose Fiber-Reinforced Polypropylene, Jan-Christoph Zarges, Univesithi ea Kassel
9-9:30 am: Phello ea ho Omisa ka Leqhoa ho Morphology ea Dried Cellulose Nanocrystals (CNCs) le Tensile Properties of Poly(lactic) Acid-CNC Composites, Nicole Stark, USDA Forest Service, Forest Products Lab
9:30-10 am: Liphello tsa Trisnonylphenyl Phostite ho Mechanical Property of Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate), Takashi Kuboki, University of Western Ontario
10-10:30 am: Monyetla oa Biocarbon joalo ka Matlafatso ea PBT ho Likopo tsa Likoloi, Boon Peng Chang, Univesithi ea Guelph
10:30-11 am: Crystallization Behaviour of PLA Composite Nanofibers ka Annealing, Jian-hua Hou, Univesithi ea Zhengzhou
8:30-9 am: Stiffer Is Better: The Case for Carbon-Fiber-Filled Thermoplastics, Philip Schell, Zoltek
9-9:30 am: Novel High-Performance Chepped Strand Glass Fiber bakeng sa Reinforcing Polypropylene-ThermoFlow 641, Derek Bristol, Johns Manville
10-10:30 am: Basics and Emerging Technologies of Fiber Sizing and Interfacial Adhesion, Steve Bassetti, Michelman Inc.
11-11:30 am: Affordable Recycled Carbon Fiber for Additive Manufacturing (3D Printing) le Automotive Thermoplastics, Andrew Maxey, Vartega Inc.
8-8:30 am: Digital Printing Technologies for Plastics: Tsepamisa maikutlo ho Color Inkjet le Laser Marking, Scott Sabreen, The Sabreen Group
9:30-10 am: Likopo tsa Low-Energy eBeam Curing Technology ho Consumer Product Flexible Packaging Applications, Anthony Carignano, eBeam Technologies
10-10:30 am: Khetho e Ntšo ea Carbon bakeng sa Katleho ka Phetiso ea Laser Welding and Joining, Scott Sabreen, The Sabreen Group;Avraham Benatar, Univesithi ea Ohio State
8-8: 30 am: Ntlha ea bohlokoa: Theknoloji eohle e Akaretsang ea Extrusion bakeng sa ho Hlahisa Lifilimi tse ngata ka nako e le 'ngoe tsa Bioriented, Adolfo Edgar, Kuhne Anlagenbau GmbH
9-9:30 am: New Surface Treatment Protocol Discovery for Extrusion Coating, Rory Wolf, ITW Pillar Technologies
10-10: 30 am: Biaxially Oriented Polyethylene (BOPE) Films E entsoeng ka Tenter Frame Process and Applications It, Yijian Lin, Dow Chemical Co.
10:30-11 am: Biaxially Oriented Barrier Film (BOPP) With Nanostructured Additives, Krishnamurthy Jayaraman, Michigan State University
11-11: 30 am: Mokhoa oa ho lekanya ts'ebetso ea oksijene ka har'a Packaging e Tiisitsoeng ea Flexible, Alejandro Serna, ICIPC
8-8: 30 am: Phetoho le Khatello ea Khatello ea Likarolo tse bōpiloeng ka Ente ka mor'a ho kenngoa sebakeng se entsoeng, Zhiliang Fan, Moldflow R & D Center, Autodesk
8:30-9 am: Moldflow Optimization of Microcavities Filling during Injection Molding Process, John Coulter, Lehigh University
9-9: 30 am: Ho Ithuta ka Tebile ho CAE Ho Thehiloe ho Kopanyo ea Taguchi Method le Neural Network, Yu-Wei Chen, Chung Yuan Christian University
9:30-10 am: Mokhoa oa ho Sebelisa CAE ho Hlahlobisisa Bothata ba Ts'ebetso e Tlas'a Ts'ebetso ea Mochini o neng o le Teng ka Enteng Molding to Face Automation Challenge, Chao-Tsai Huang, Univesithi ea Tamkang
10-10: 30 am: Ho Sebelisa Mohlala o Mocha oa Anisotropic Rotational Diffusion ho Ntlafatsa Boprofeta ba Li-Fibers tse Khutšoane ka Thermoplastic Injection Molding, Alexander Bakharev, Autodesk
10:30-11 am: Empirical Modeling and Simulation of the Microstructure Replication in Injection Molding, Torben Fischer, Institute of Plastics Processing (IKV) Univesithing ea RWTH Aachen
11-11:30 am: Thuto ea Simulation ea Ente Compression Molding Process bakeng sa 0.6mm Thin Polymeric Microfluidic Chip, Ge Chen, Singapore Institute of Manufacturing Technology
8:30-9 am: Plenary: Likoloto tsa Lipatlisiso bakeng sa Indasteri ea Plastics, Michael Devereux, Mueller Prost CPAs + Business Advisors
9-9:30 am: Phello ea Mould Coatings ka Phallo Resistance in Thin-Wall Injection Molding of Polystyrene Parts, Marco Sorgato, University of Padova
11-11: 30 am: Fetola Molds bakeng sa Tsoelo-pele e Atlehang ea Bareki / Prototype, Tom Worcester, Meusburger USA
8-8:30 am: Phello ea Foam Density on Elastomeric Nanocomposite Foams Based on Polyisoprene Rubber, Ali Vahidifar, University of Bonab
8:30-9 am: Phello ea Likarolo tse Bonolo le Liemeli tsa Nucleation ho Thermoplastic Polyurethane Foam, Shu-Kai Yeh, Univesithi ea Naha ea Taiwan ea Saense le Theknoloji.
9-9:30 am: Patlisiso ea Khopolo-taba le ea Teko ea Kholo ea Likhopo ka Moulding ea Ente ea Foam e Phahameng ea Khatello e Phahameng, Chongda Wang, Univesithi ea Toronto
9:30-10 am: Khatello ea ho Thatafala ha Linear Polymer E Matlafalitsoeng ke Lithaele Tse Fokolang Mocheso, Sundong Kim, Univesithi ea Vermont
10-10:30 am: Ho Matlafatsa Ts'ebetso ea Ts'ireletso ea Motlakase ea Likopano tsa PVDF/MWCNT Ka ho Foaming, Chenyinxia Zuo, Univesithi ea Toronto
10:30-11 am: Foams Piezoelectric With High Thermal Stability and Flexibility, Zhe Liu, Florida State University
11-11: 30 am: Resorcinol Formaldehyde Airgel Nanonetwork Structural Assembly le Thermal Properties Correlation, Mohammed Alshrah, Univesithi ea Toronto
9-9:30 am: Lipompo tsa Insulin tse Aparehang: Moralo le Tekanyetso ea Ts'ebetso ea Letsatsi le Letsatsi, Hossam Metwally, Ansys Inc.
9:30-10 am: Moralo oa Novel oa Li-Siloxane tse Fetisitsoeng tsa Organo-Modified bakeng sa Kalafo ea Bokaholimo ba Likokoana-hloko le Li-Filler, Ido Offenbach, Evonik
10-10:30 am: Mabone a Likoloi ka Metsoako e Fokotsoeng ea Polyamide, Ying Shi, A. Schulman Inc.
10:30-11 am: Xenoytm ENH2900 for High Chemical Resistance & Non-Br/Cl FR Applications, Emily He, Sabic
11:30 am-12 pm: Litharollo tsa Sebele tsa Ketsiso tse Sebelisang FEA bakeng sa Moralo, Ntlafatso le Boqapi ba Plastiki, Arindam Chakraborty, Virtual Integrated Analytics Solutions.
1:30-2 pm: Ho hokahanya Rheology ea Polyolefin Elastomers ho Phatlalatso ka Polypropylene Matrix ka Mohlala le Liteko ka Masimo a Bonolo a Phallo, Jeff Munro, Dow Chemical Co.
2:30-3 pm: Polelo e Matla ea ho Kena ha Metsi bakeng sa Ts'ebetso ea Pushback ho Molding ea Ente e Thusang ka Metsi, Jim Hsu, CoreTech System
3-3:30 pm: Kamoo Plastiki e Thusang Kateng ho Hlōla Mathata a Macha a Motlakase oa Likoloi, Werner Posch, Sehlopha sa Draexlmaier
3:30-4 pm: Nts'etsopele ea Li-Composites tsa Low-Emission Polyolefin bakeng sa Interiors tsa Likoloi, Tanmay Pathak, A. Schulman Inc.
4-4:30 pm: Phello ea Paterone ea lijo-thollo le litaba tsa Talc ho Scratch le Mar Behaviors of Textured Thermoplastic Olefins, Shuoran Du, Texas A&M University
4:30-5 pm: Vehicle Lightweighting le Ntlafatso ea Crashworthiness: Plastics and Hybrid Solutions, Fred Chang, Sabic
5-5:30 pm: Motsoako oa Novel-Filler-Reinforced bakeng sa likarolo tsa ka Hare-hare tsa Likoloi, Cheolhee Park, GS Caltex
5:30-6 pm: Bumper to Bumper: Ho Tlosa Litšila ho Likarolo Tsa Plastiki tse Molded Wwith Dry Ice, Steve Wilson, Cold Jet LLC
1:30-2 pm: Synthesis, Characterization and Water Application of Microcellular Injection Molded PPGMA/MMT Nanocomposites, Shyh-Shin Hwang, Chien Hsin University of Science and Technology
2-2:30 pm: Tokisetso ea Polypropylene Sing-Polymer Composites With Graphene Nanoplatelets ka Film-Stacking, Mingwang Shao, Beijing Institute of Technology
2:30-3 pm: Ho Arola Phello ea Tšebelisano ea Polymer-Filler ho Ntlafatso ea Thepa ea Polymer Composite: Mohlala oa Polypropylene/Halloysite Hybrids, Tong Wei, Northwestern University.
3-3:30 pm: Lithuto tsa Numerical le tsa Teko mabapi le Phallo le Warpage Nakong ea Ts'ebetso ea Ho Fetisetsa Resin Transfer, Sejin Han, Autodesk
3:30-4 pm: High Fracture Resistance, Filler Adhesion and Disspersion in Epoxy Carbon Nanofiber Composites, Muhammad Anwer, Univesithi ea Toronto
4-4:30 pm: Ho Ntlafatsa Ts'ebetso ea Ultrasonic ea CNT Nanopaper/Solventless Epoxy Prepreg, Dan Zhang, Univesithi ea Ohio State
4:30-5 pm: In Situ Vitamin C Phokotso ea Graphene Oxide bakeng sa Ho Lokisetsa Flexible TPU Nanocomposites Ka High Dielectric Permittivity, Han-xiong Huang, South China University of Technology
2-2:30 pm: Induction Heat Cool With Sabic Resins: Intro to High-Definition Plastics, Jos van Gisbergen, Sabic
4-4: 30 pm: "Smart Factories": Bokamoso ba Tlhahiso ea Plastiki e nang le 4.0 Connectivity and Condition Monitoring System (CMS), Markus Klaus, Wittmann Battenfeld
4:30-5 pm: Ho Ntlafatsa ho Nepaha ha Lipapiso tsa ho Tlatsa Mold ka Lintlha tsa Teko tse Tsoang ho Fast Scanning Chip Calorimetry, Anne Gohn, Univesithi ea Penn State
5-5:30 thapama: Likarolo tsa Ho Enta ka Ente ka Sekala se Kopantsoeng sa All-Inkjet se Hatisitsoeng bakeng sa Tlhokomelo ea Boemo, Thomas Mitterlehner, Ph.D.seithuti, Johannes Kepler University Linz
1:30-2 pm: New Technology in Nonhalogen Flame Retardants: Oxyimides, Rudolf Pfaendner, Fraunhofer Institute
2-2:30 pm: Mekhoa ea ho Tsamaisa Thekiso ea NHFR Technologies: A European Perspective, Maryline Desseix, PolyOne Corp.
3-3:30 pm: Ho Leba Khabone ho Mohopolo oa Kaho: Liphephetso tsa Thepa le Kopano, Mark Goulthorpe, Setsi sa Theknoloji sa Massachusetts.
3:30-4 pm: Ho Finyella Kamohelo ea Khoutu ea Kaho ea Machabeng ea Lisebelisuoa tsa Kaho tsa Polymeric: Mathata a Baqapi ba Lintho le Likopano, Nicholas Dempsey, Worcester Polytechnic Institute.
4-4:30 pm: Li-Retardants tsa Lelakabe ho Lihlahisoa tsa Bareki: Kakaretso le Pono mabapi le Thibelo e Reriloeng ea CPSC, Jared Schwartz, Exponent;Andrew Worthen, Exponent
4:30-5 pm: Ntlafatso le Khoebo ea NHFR Technologies, Nicholas Dempsey, Worcester Polytechnic Institute;Maryline Desseix, PolyOne;Mark Goulthorpe, Massachusetts Institute of Technology;Gordon Nelson, Setsi sa Theknoloji sa Florida;Rudolf Pfaendner, Setsi sa Fraunhofer;Jared Schwartz , Exponent;Andrew Worthen, Exponent
1:30-2 pm: Modelling Doming Deflection of Caps and Closures With Finite Element Method, Wenbo Xu, Dow Chemical Co.
2-2:30 pm: Quasi-Static, Nonlinear, Explicit Finite Element Analysis of Small PET Bottles, Naser Imran Hossain, Niagara Bottling
2:30-3 pm: Moralo bakeng sa Tlhahiso: 3D-CAD Design Methodology for Spiral Milled Polymer Processing Tools, Phil Hungenberg, Universität Duisburg-Essen
3-3:30 pm: Thero ea Sehlahisoa e Thehiloeng ho Tsebo le Moralo oa Likarolo tse Mold ea Ente, Rene Andrae, Univesithi ea Duisburg-Essen
3:30-4 pm: Tšusumetso ea Phekolo ea Thermal ho Mechanical Properties ea Thermoplastic Composites E Fumanetsoeng ke Mokhoa o Moholo oa Khatiso ea 3D, Miguel A. Hidalgo Salazar, Universidad Autónoma de Occidente
4-4: 30 pm: E, U ka Tlola Melao e itseng ea Moralo 'me U ntse U E-na le Sehlahisoa se Atlehileng: Ho Sheba ka mokhoa o utloahalang ka liphello, Vikram Bhargava, Mongoli, Mokoetlisi le Moeletsi.
4:30-5 pm: Polypropylene/ Polyvinylidene Fluoride Fibrous Water/Fuel Filters E Hlahisoe ke Unique Multilayer Co-Extrusion Process, Cong Zhang, Case Western Reserve University
5-5:30 pm: Tekolo ea Tekheniki ea Loctite HY4060GY: Phetoho e Ntle bakeng sa Traditional 2K 5-Minute Epoxies, Matthew Miner, Henkel
5:30-6 pm: Ho Sebelisa Litšenyehelo ho Kopanela Lilemo Tse Sekete Mosebetsing, Laurel Bougie, aPriori Technologies
1:30-2 pm: Tšusumetso ea Mekhatlo ea Ts'ebetso e Kopantsoeng ka Phatlalatso le Lintho tsa Material tsa Graphene-Based PP Composites Ho Sebelisa Twin-Screw Extruder Tlas'a Maemo a amanang le Indasteri, Maximilian Adamy, IKV Aachen
2:30-3 pm: Tšebeliso ea Thermoplastic Polyurethane Foaming in Handrail Extrusion, Qingping Guo, EHC Canada
3-3:30 pm: Flexural Testing ea PET-NanoFiber le PP Foamed Composites, Lun Howe Mark, Univesithi ea Toronto
3:30-4 pm: Khōlo e Sirelelitsoeng ea Biofilm ho Macroporous Polyvinilidene Fluoride Carriers for Biological Organic Removal From Municipal Wastewater, Pardis Ghahramani, Ph.D.seithuti, Univesithi ea York
4-4:30 pm: Taolo ea Tšusumetso le Tšireletso bakeng sa ho Bapala Sebaka sa ho Bapala Ho Sebelisa Polyolefin Particle Foam e Atolositsoeng: Lisebelisoa le Meetso e Ncha, Steven Sopher, JSP International
4:30-5 pm: Ultalow Density Foams of Nanocrystalline Cellulose e Matlafalitsoeng ka Polyvinyle Alcohol, Nahal Aliheidari, Washington State University
5-5:30 pm: Mokhoa oa ho Bona le ho Lekanya Khatello ea Phallo ea Polasetiki Tlas'a Maemo a Shear, Taylor Ducharme, Univesithi ea Vermont.
5:30-6 pm: Ho Rafa Boleng ho Tsoa ho Oil Sands Tailings Ponds, Pavani Cherukupally, Univesithi ea Toronto.
6-6: 30 pm: Li-Polyamides tse Matle haholo tse entsoeng ka Cast Polyamide 6 Recyclates, Benjamino Rocco Formisano, Institut für Kunststofftechnik-University of Stuttgart
2:30-3 pm: Nylon 6/6 Rich Co- le Terpolymers: Kamoo Tuning Thermal Behaviour Ntlafatsa Tshebetso le ho Nolofatsa Dibaka tse Ntjha tsa Applicaiton, Jacob Ray, Ascend Performance Materials
3-3:30 pm: Mophato o Mocha oa High Melt Strength Polystyrene bakeng sa Mmaraka oa Foam oa XPS, Ted Harris, Total Petrochemicals le Refining USA Inc.
4:30-5 pm: Metsoako e Tlaase ea Phallo: Litlhaloso tsa Likoloi le Likopo, Tanmay Pathak, A. Schulman Inc.
5-5:30 pm: Ntlafatso ea Lifilimi tsa Ts'ireletso ea Ts'ireletso ka Cyclic Olefin Copolymers, Paul Tatarka, Topas Advanced Polymers Inc.
1:30-2 pm: Tšusumetso ea Khatello ea Khase ea Khatello ea Boitšoaro bo Foaming le Cell Morphology ea Flexible Polyurethane Foam, Daniel Schneider, Setsi sa Ts'ebetso ea Plastic ho RWTH Aachen University.
2:30-3 pm: New Generation HDPE for Pressurized Applications: Beyond Pe100, Jonathan Rabiei Tabriz, Sabic Petrochemicals
3-3:30 pm: SABIC Solutions for Personal Hygiene Applications: Industry Trends le SABIC Offerings and Developments, Jelena Bozovic-Vukic, Sabic
5-5:30 pm: Stylight: Tharollo e Ncha ea Material for Lightweight Design, Brian Haggart, Ineos Styrolution
O na le maikutlo mabapi le pale ee?A na u na le maikutlo ao u ka ratang ho a arolelana le babali ba rona?Plastics News e ka thabela ho utloa ho tsoa ho uena.Romella lengolo la hau ho Editor ho [imeile e sirelelitsoeng]
Litaba tsa Plastics li akaretsa khoebo ea indasteri ea polasetiki ea lefats'e.Re tlaleha litaba, re bokella lintlha le ho fana ka tlhahisoleseling e nakong e fang babali ba rona monyetla oa tlholisano.
Nako ea poso: Oct-27-2020